Share this product

Cable Railing Post - Fascia Mount, Terminal

This product ad may change over time

Share

Cable Railing Post - Fascia Mount, Terminal

This post attaches to the side of your deck and is part of our aluminum cable railing system. Use one on each end of a cable railing run, as this reinforced post is designed for anchoring the ends of your cable.The foundation of any cable rail system is where the cables begin and end. Our FASCIA MOUNT TERMINAL POST is engineered specifically t…

New content will be added above the current area of focus upon selection

This post attaches to the side of your deck and is part of our aluminum cable railing system. Use one on each end of a cable railing run, as this reinforced post is designed for anchoring the ends of your cable.The foundation of any cable rail system is where the cables begin and end. Our FASCIA MOUNT TERMINAL POST is engineered specifically to withstand the applied stress when each wire rope is tensioned. Each aluminum railing post is manufactured from 6063 T6 aluminum with reinforced walls. Avoid competitor hollow posts that are designed for glass infill. When the cables are tightened in these cable railings, the posts tend to deflect, so the installer must decrease cable tension to reduce the bending.Terminal posts come either pre-drilled with powder-coated holes to eliminate many hours of installation labor, or undrilled (for surface mount fittings or custom drilling during installation). The drilled posts sold on this page are for flat runs. For stair runs, buy undrilled or call us for angled hole drilling.The FASCIA MOUNT TERMINAL POST mounts directly to the rim joist or fascia board by attachment hardware. Usually these are lag bolts (sold separately).For additional corrosion prevention, purchase Grommets for each hole. Our grommets can also be used to keep the cables from rattling against post walls in windy areas.NOTE: SOME POST VARIATIONS ARE OVERSIZED AND MUST BE CUT DOWN ON JOB SITE. SPECIFICATIONS Available for either 36" or 42" rail heights. 2 3/8" square Powder Coat Finish: Baked on color coating that meets AAMA 2604 standards. Anodized Finish: Brushed black or clear electrochemically-achieved protective outer layer for increased corrosion resistance. 13 9mm predrilled holes (requiring 13 cable runs), for a total railing height of 42" above deck boards. 11 9mm predrilled holes (requiring 11 cable runs), for a total railing height of 36" above deck boards. Qty (2) mounting holes must be drilled . Use the CableView Railing™ WORKSHEET to design your aluminum railing system and consider the following: Are you going to DECK MOUNT or FASCIA MOUNT your posts? Which top rail will I use? Use either PROFESSIONAL SWAGING SERVICE or HAND SWAGING . If PROFESSIONAL SWAGING SERVICE is used at both ends of the cable run: Use DECK OR FASCIA MOUNT TERMINAL POSTS for every post in your aluminum handrail, including double offset posts at the corners. This will allow the attached fitting to pass through every post in the system.If HAND SWAGING your assemblies (RECOMMENDED) : Minimum of 2 DECK OR FASCIA MOUNT TERMINAL POSTS are required for each cable run (wherever your cable begins and ends). If your cable run also has 90 degree corners, use double INTERMEDIATE POSTS at each corner. Use DECK OR FASCIA MOUNT INTERMEDIATE POSTS spaced evenly (4' Max) for the remainder of the posts. CABLE CRIMPERS and CABLE CUTTERS are required.If you need any help, send us an email at quotes@stainlesscablerailing.com or call 1-888-686-7245 (RAIL) . For a free estimate, fill out an ESTIMATE REQUEST FORM and either fax or email it to us. We will respond within 24 hours. Be sure to take a look at our cable railing videos and WORKSHEETS for more railing inspiration and information. Product # 710227, 710210, 710692, 710685, 729844, 729851, 729868, 729875, 729882, 734480, 734497, 734503, 734510, & 734527

See more below

S

Stainless Cable & Railing

$115.46

Visit site

Description

This post attaches to the side of your deck and is part of our aluminum cable railing system. Use one on each end of a cable railing run, as this reinforced post is designed for anchoring the ends of your cable.The foundation of any cable rail system is where the cables begin and end. Our FASCIA MOUNT TERMINAL POST is engineered specifically to withstand the applied stress when each wire rope is tensioned. Each aluminum railing post is manufactured from 6063 T6 aluminum with reinforced walls. Avoid competitor hollow posts that are designed for glass infill. When the cables are tightened in these cable railings, the posts tend to deflect, so the installer must decrease cable tension to reduce the bending.Terminal posts come either pre-drilled with powder-coated holes to eliminate many hours of installation labor, or undrilled (for surface mount fittings or custom drilling during installation). The drilled posts sold on this page are for flat runs. For stair runs, buy undrilled or call us for angled hole drilling.The FASCIA MOUNT TERMINAL POST mounts directly to the rim joist or fascia board by attachment hardware. Usually these are lag bolts (sold separately).For additional corrosion prevention, purchase Grommets for each hole. Our grommets can also be used to keep the cables from rattling against post walls in windy areas.NOTE: SOME POST VARIATIONS ARE OVERSIZED AND MUST BE CUT DOWN ON JOB SITE. SPECIFICATIONS Available for either 36" or 42" rail heights. 2 3/8" square Powder Coat Finish: Baked on color coating that meets AAMA 2604 standards. Anodized Finish: Brushed black or clear electrochemically-achieved protective outer layer for increased corrosion resistance. 13 9mm predrilled holes (requiring 13 cable runs), for a total railing height of 42" above deck boards. 11 9mm predrilled holes (requiring 11 cable runs), for a total railing height of 36" above deck boards. Qty (2) mounting holes must be drilled . Use the CableView Railing™ WORKSHEET to design your aluminum railing system and consider the following: Are you going to DECK MOUNT or FASCIA MOUNT your posts? Which top rail will I use? Use either PROFESSIONAL SWAGING SERVICE or HAND SWAGING . If PROFESSIONAL SWAGING SERVICE is used at both ends of the cable run: Use DECK OR FASCIA MOUNT TERMINAL POSTS for every post in your aluminum handrail, including double offset posts at the corners. This will allow the attached fitting to pass through every post in the system.If HAND SWAGING your assemblies (RECOMMENDED) : Minimum of 2 DECK OR FASCIA MOUNT TERMINAL POSTS are required for each cable run (wherever your cable begins and ends). If your cable run also has 90 degree corners, use double INTERMEDIATE POSTS at each corner. Use DECK OR FASCIA MOUNT INTERMEDIATE POSTS spaced evenly (4' Max) for the remainder of the posts. CABLE CRIMPERS and CABLE CUTTERS are required.If you need any help, send us an email at quotes@stainlesscablerailing.com or call 1-888-686-7245 (RAIL) . For a free estimate, fill out an ESTIMATE REQUEST FORM and either fax or email it to us. We will respond within 24 hours. Be sure to take a look at our cable railing videos and WORKSHEETS for more railing inspiration and information. Product # 710227, 710210, 710692, 710685, 729844, 729851, 729868, 729875, 729882, 734480, 734497, 734503, 734510, & 734527

Specifications

Bolt Hole Quantity	2
Diameter	2 3/8"
Dimensions	36" or 42"
Certification	AAMA 2604 standards
Compatibility	Aluminum cable railing system, wire rope, surface mount fittings, hand swaging or professional swaging service, grommets, lag bolts
Connection Type	Attachment hardware
Color	Baked on color coating or brushed black or clear
Application	Cable railing system
Brand	CableView Railing™
Base Type	Fascia mount
Durability	Increased corrosion resistance
Condition	New
Design	Reinforced walls, pre-drilled or undrilled, powder-coated or anodized finish, square shape
Compatibility with other parts	Wire rope, surface mount fittings, grommets, lag bolts
Compatibility with other systems	Aluminum cable railing system, hand swaging or professional swaging service
Configuration	Terminal post